Single Component Hand Scraped Thick Film Polyurea

• Customization: Available
• Appearance: Liquid
• Drying Method: Moisture Cured
• Model NO.: STWD9526
• Formation Mechanism: Conversion Type
• Transport Package: Iron Bucket Packaging
• Specification: 210L
• Trademark: STWD
• Origin: China
• Production Capacity: 80000kg/Day

Product Description

 
Application scope         
Waterproof of construction, water conservancy, transportation, chemical and power plants, such as the crack repair of highway, pavement, airport runway, leak repair of water conservancy, offshore dam and port dock repair etc.

Product information 

Item	Results
Appearance	Color is adjustable
Specific gravity (g/cm^3))	1.1
Viscosity (cps )@20ºC	10000-30000
Solid content (%)	≥80
surface dry time (hrs)	1-3
Pot life (hrs)	0.5h

Physical properties

Item	Test standard	results
Hardness (Shore A)	GB/T23446-2009	88
Elongation (%)	GB/T23446-2009	320
tensile strength (Mpa)	GB/T23446-2009	20
Tear strength (kN/m)	GB/T23446-2009	60
abrasion resistance(750g/500r),mg	HG/T 3831-2006	8
Adhesive strength (Mpa) steel base	HG/T 3831-2006	10
Adhesive strength (Mpa) concrete base	HG/T 3831-2006	3.3
impact resistance (kg.m)	GB/T23446-2009	1.0
Density (g/cm^3)	GB/T 6750-2007	1.25

Chemical properties

Acid resistance 30%H2SO4 or10%HCl,30d	no rust, no bubbles, no peel off
Alkali resistance 30%NaOH, 30d	no rust, no bubbles, no peel off
Salt resistance 30g/L,30d	no rust, no bubbles, no peel off
Salt spray resistance, 2000h	no rust, no bubbles, no peel off
Oil resistance	no bubbles, no peel off
0# diesel, oil, 30d	no rust, no bubbles, no peel off
(For reference: pay attention to the influence of ventilation, splash and spillage. Independent immersion testing is recommended if requiring detail data.)

Application instructions
Environment temperature: -5 ~35ºC
Relative humidity: 35-85%
Dew point: when apply on metal surface, the temperature must be 3ºC higher than dew point.

Application guidance
Recommended dft: 500-1000um (or based on the design requirements)
Recoat interval: 2-4h, if exceed 24h or have dusts on the surface, use sandpaper to blasting then apply it.
Recommended application method: use scraper to scratch.

Notice
It can be used in the temperature below 10ºC. When apply in extreme low temperature, keep the coating barrel in the air conditioning room for 24 hrs.
STWD advises to mix the coating barrel uniform, seal the package well after use to avoid moisture absorption. Not to put the poured out material into the original barrel again.
Viscosity is fixed before shipped, thinner shall not be random added. Instruct the manufacturer in special situation to add thinner.

Curing time

Substrate temperature	Surface dry time	Foot traffic	Solid cure
+10ºC	4h	24h	7d
+20ºC	1.5h	8h	6d
+30ºC	1h	6h	5d

Shelf life
Storage temperature of environment: 5-35ºC
* shelf life: 6 months (sealed)
* store in cool and ventilated place, avoid sunshine direct exposure, keep away from heat.
* Package: 4kg/barrel, 20kg/barrel.

Product health and safety information 
For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Material Safety Data Sheet containing physical, ecological, toxicological and other safety related data.

Integrity declaration    
STWD guarantee all technical data stated in this sheet are based on laboratory tests. Actual testing methods may vary due to different circumstances. Therefore please test and verify its applicability. STWD does not take any other responsibilities except the product quality and reserve the right of any modifications on the listed data without prior notice.